BigJohny

Posted an answer Two solid shafts are connected by gears as shown. Knowing that G = 77.2 GPa for each shaft, determine the angle through which end A rotates when TA – 1200 nm Thank you soo much for the help.	7 days ago	5
Asked a question A992 steel shaft is made from two segments. AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uniform distributed torque of 60 lb in./in. along segment CB, determine the absolute maximum shear stress in the shaft. A992 steel shaft is made from two segments. AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uniform distributed torque of 60 lb...	7 days ago	2
Asked a question The two solid steel shafts shown in the following figure are coupled together using the meshed gears. Determine the angle of twist of end A of shaft AB when the torque T = 45Nm is applied. shaft DC is fixed at D. Each shaft has a diameter of 20 mm. G = 80 GPa. Example 5.7: The two solid steel shafts shown in the following figure are coupled together using the meshed gears. Determine the angle of twist of end A of shaft AB when the torque T = 45Nm is applied....	November 14, 2024	2
Asked a question If the shaft is subjected to a uniform distributed torque of t = 20 kN m/m, determine the maximum shear stress developed in the shaft. The shaft is made of 2014-T6 aluminum alloy and is fixed at A and C. If the shaft is subjected to a uniform distributed torque of t = 20 kN m/m, determine the maximum shear stress developed in the shaft. The shaft is made of 2014-T6 aluminum alloy and is fixed at A and...	November 14, 2024	2
Asked a question The shaft is made of A-36 steel and is fixed at end D, while end A is allowed to rotate 0.005 rad when the torque is applied. Determine the torsional reactions at these supports. The shaft is made of A-36 steel and is fixed at end D, while end A is allowed to rotate 0.005 rad when the torque is applied. Determine the torsional reactions at these supports.	November 14, 2024	2
Asked a question The solid steel shaft AC has a diameter of 25 mm and is supported by smooth bearings at D and E. it is coupled to a motor at C, which delivers 3 kW of power to the shaft while it is turning at 50 rev/s. If gear A and B remove 1 kW and 2 kW, respectively, determine the maximum shear stress developed in the shaft within regions AB and BC. The shaft is free to turn in its support bearings D and E. The solid steel shaft AC has a diameter of 25 mm and is supported by smooth bearings at D and E. it is coupled to a motor at C, which delivers 3 kW of power to the shaft while it is turning at 50 rev/s....	November 14, 2024	2
Asked a question the link acts as part of the elevator control for a small airplane. If the attached aluminum tube has an inner diameter of 25 mm and a wall thickness of 5 mm, determine the maximum shear stress in the tube when the cable force of 600 N is applied to the cables. the link acts as part of the elevator control for a small airplane. If the attached aluminum tube has an inner diameter of 25 mm and a wall thickness of 5 mm, determine the maximum shear stress in the...	November 14, 2024	2
Asked a question Two solid shafts are connected by gears as shown. Knowing that G = 77.2 GPa for each shaft, determine the angle through which end A rotates when TA - 1200 nm Two solid shafts are connected by gears as shown. Knowing that G = 77.2 GPa for each shaft, determine the angle through which end A rotates when TA - 1200 nm	November 14, 2024	2
Asked a question The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5kNm is applied to end A, determine the maximum shear stress in each material. Sketch the shear stress distribution. The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5kNm is applied to end A, determine the maximum shear stress in each material. Sketch the shear stress distribution.	November 14, 2024	2
Asked a question A rod is made from two segments:AB is steel and BC is brass. It is fixed at its ends and subjected to a torque of T = 680 Nm If the steel portion has a diameter of 30 mm, determine the required diameter of the brass portion so the reactions at the walls will be the same Gst = 75GPa, Gbr = 39 GPa. A rod is made from two segments:AB is steel and BC is brass. It is fixed at its ends and subjected to a torque of T = 680 Nm If the steel portion has a diameter of 30 mm, determine the required diameter...	November 14, 2024	2
Registered	November 14, 2024	10

@bigjohny